You are here

LineBacker® 61™ NSF Certified Isolating Gaskets/Kits

The LineBacker® 61™ sealing system uses a rectangular sealing element in combination with a unique groove design to effectively seal and isolate flanges for potable water and other low-pressure fluid piping applications

NSF/ANSI Standard 61 establishes minimum health effects requirements for the chemical contaminants and impurities that may be indirectly imparted to drinking water. The LineBacker® 61™ Sealing/Isolating gasket is certified to conform with all criteria associated with NSF health effects testing, certification and production facility inspections.

Of particular importance with respect to NSF/ANSI Standard 61, is the micro-exposure of the sealing element (EPDM) within the G-10 Epoxy Glass retainer material. In addition to providing positive sealing characteristics relative to the fluid flowing in the pipe, the sealing element is also fully encapsulated between the flange and GRE retainer, reducing exposure of the sealing element to harsh outside atmospheric conditions.

For more information regarding NSF, please contact GPT Engineering.

FEATURES AND BENEFITS

  • Guards against blowouts¹
  • Usable with any type of flange or combination of flanges
  • Lowest possible clamp and compressive load to effect a seal
  • High dielectric strength 800v / mil
  • Water absorption less than 0.10%
  • All standard ANSI and AWWA flange sizes from 1/2" and above

SPECIFICATIONS

Retainer Physical Properties

Max Temperature  +302°F /+150°C

 

ASTM Test Method G-10 Epoxy Glass
D149 Dielectric Strength: Volts/Mil(Short Time):690
D229 Water Absorption: 0.22 %
D790 Flexural Strength: LW 66,000 psi / CW 60,000 psi (413,685 kPa)
D785 Hardness Rockwell "M": 99
D638 Tensile Strength: LW 45,000 psi / CW 39,000 psi (310,264 kPa)
D732 Shear Strength: 19,000 psi (151,684 kPa)

Seal Element Physical Properties

Temperature Range EPDM
Fahrenheit -40° to +212°
Celsius -40° to +100°

 

APPLICATIONS

  • Potable water and other fluids

ADDITIONAL INFORMATION

NSF 61 FLANGE GASKET SPECIFICATION

Materials for flange isolation kits on pipes containing drinking/potable water (up to 280ºF (138ºC)) shall consist of the following components:

Isolating and Sealing Gasket

The full faced, NSF 61 certified, isolating and sealing gasket shall be LineBacker® 61™ Sealing Gasket (LB61) - Type “E”, 1/8” thick, G-10 retainer containing a precision tapered groove to accommodate the controlled compression of a EPDM quad-ring sealing element. Sealing element placement shall accommodate either flat, raised face or RTJ flanges. The quad-ring seal shall be pressure energized. The G-10 retainer shall have a 550 volts/mil dielectric strength and a minimum 50,000 psi compressive strength. The full-faced flange isolating gasket (weld-neck) shall be equal to or slightly smaller than the bore of the flange; (slip-on) shall be equal to or smaller than the I.D. of mating pipe.

Full Length Bolt Isolating Sleeves

One full length G-10 sleeve (extending half way into both steel washers) for each flange bolt. The G-10 shall be a 1/32” thick tube with a 400 volts/mil dielectric strength and water absorption of 0.10% or less.

Washers

Two, 1/8” thick, G-10 isolating washers for each bolt. Their compressive strength shall be 50,000 psi, dielectric strength 550 volts/mil and water absorption 0.10% or less. Two, 1/8" thick zinc plated, hot-rolled steel washers for each bolt. The I.D. of all washers shall fit over the isolating sleeve and both the steel and isolating washers shall have a same I.D. and O.D.

Quality - (Made in U.S.A - A.R.R.A Compliant)

Flange isolating kits shall be manufactured at a facility that has a registered ISO 9001 Quality Management System. Submittals shall include copy of valid ISO registration and NSF 61 certification.

Before Tightening

The flange faces come into contact with the sealing elements, which extend slightly above the surface of the retainer. As the flange is tightened the sealing elements are compressed and move sideways into the inclined portion of the groove, developing a high unit pressure against the flange faces.

After Tightening

The flange faces have come into firm contact with the retainer, thus encapsulating the sealing elements within grooves. At the same time, the unique LineBacker® seal configuration provides elastic memory for elastomers not normally associated with this characteristic - resulting in a simple flat gasket with extremely high loading and self energizing characteristics without adverse cold flow problems.

TYPE E GASKET (Full Face)

The gasket retainer extends out to the O.D. of the flange. Holes are cut at the bolt circle to accommodate threaded studs or bolts.  If in doubt about whether to use an “E” type gasket or an “F” type gasket, select an “E” type gasket as it will perform well in both flange types.  An “F” type gasket only performs well in “F” type flange design.

TYPE F GASKET

The gasket retainer extends out to the I.D. of the bolt circle.

Resources

Customer Service

Customer Service Inquiries
Phone (Office):
Fax:
+1 800 543 0598
Regions:
North America
Sales Manager - China & Taiwan
Email Address:
Phone (Mobile):
Regions:
Asia, China, People's Republic of

Product Manager

Product Manager - Isolation Products
Tim Hurley
Phone (Office):
Fax:
+1 303 988 1922
Regions:
Africa, Asia, Central America, Europe, Middle East, North America, Oceania, South America
Product Line Technical Specialist
Phone (Office):
Regions:
North America, South America

Sales

Customer Service Inquiries
Phone (Office):
Fax:
+1 800 543 0598
Regions:
North America
Southeastern USA Sales Manager - TX, AR, KS, OK, LA, MS, AL
Peter Aubin
Phone (Office):
Fax:
+1 303 988 1922
Regions:
North America
Western USA Sales Manager
Richard Moore
Phone (Office):
Regions:
North America
Canada Sales Manager
GlennOrmsby
Phone (Office):
Phone (Mobile):
Regions:
North America
Sales Manager - China & Taiwan
Email Address:
Phone (Mobile):
Regions:
Asia, China, People's Republic of
Business Manager - Director
Phone (Office):
Regions:
Africa, Europe, Middle East
Regional Manager
Richard Edwin
Phone (Office):
Fax:
+971 4 883 3682
Regions:
Africa, Middle East
Regional Sales Manager
Osama Gad Emam
Email Address:
Phone (Mobile):
Fax:
Regions:
Africa
Asia Pacific Regional Manager - Oceania, Bangladesh, Hong Kong & Indonesia
Hamilton Hind
Phone (Office):
Regions:
Asia, Oceania
Sales Manager - Korea, Japan & Sakhalin Island
Quentin Lee
Phone (Office):
Regions:
Asia
Regional Sales Manager
Phone (Office):
Fax:
+971 4 8833682
Regions:
Middle East
Regional Sales Director
Kishore Pradhan
Phone (Office):
Fax:
+971 4 883 3682
Regions:
Middle East
Sales
Eduardo Villasmil
Email Address:
Phone (Office):
Regions:
Central America, South America
Subject Matter Expert Oil & Gas - Malaysia, Brunei, Singapore, Philippines, Myanmar,Thailand & Vietnam
Wilson Wee
Phone (Office):
Regions:
Asia